Kawasaki ZX-10R (2008-2010) - Workshop Manual - Parts Catalogue - Wiring Schematics

KAWASAKI ZX-10R (2008-2010) - WORKSHOP, SERVICE, REPAIR MANUAL - PARTS CATALOGUE - WIRING SCHEMATICS

- English Workshop Manual, Parts Catalogue and Wiring Schematics, for motorcycles Kawasaki ZX-10R (2008-2010).

 
INDEX:

SERVICE MANUAL

- General Information
- Before starting to perform an inspection service or carry out a
- Frame Number
- Engine Number
- Overview
- Prefixes for Units:
- Units of Temperature:
- Periodic Maintenance
- The scheduled maintenance must be done in accordance with this c
- The following tables list the tightening torque for the major fa
- Inside Circlip Pliers:
- Fuel System (DFI)
- Fuel System (DFI)
- DFI System
- DFI System Wiring Schematics
- Terminal Numbers of ECU Connectors
- Main Throttle Sensor [A]
- Oil Pressure Gauge, 5 kgf/cm :
- DFI Servicing Precautions
- The warning indicator light (LED) [A] is used for the FI indicat
- NOTE
- The warning indicator light (LED) [A] is used for the FI indicat
- The main throttle sensor is a rotating variable resistor that ch
- Inlet Air Pressure Sensor Removal
- Inlet Air Temperature Sensor Removal/Installation
- Water Temperature Sensor Removal/Installation
- Atmospheric Pressure Sensor Removal
- The crankshaft sensor has no power source, and when the engine s
- The camshaft position sensor detects the position of the camshaf
- Speed Sensor Removal/Installation
- Gear Position Switch Removal/Installation
- This sensor has a weight [A] with two magnets inside, and sends
- The subthrottle sensor is a rotating variable resistor that chan
- Oxygen Sensor ##1 Removal/Installation
- Exhaust Butterfly Valve Actuator Sensor Removal/Installation
- Antenna Resistance Inspection
- ECU Communication Line Inspection
- Fuel Pump Relay Removal/Installation
- Stick Coil ##1: Service Code 51
- Radiator Fan Relay Removal/Installation
- Subthrottle Valve Actuator Removal
- Exhaust Butterfly Valve Actuator Removal
- Air Switching Valve Removal/Installation
- Oxygen Sensor Heater Removal/Installation
- Oxygen Sensor ##2 Removal/Installation
- Light (LED) Inspection
- ECU Identification
- ECU Fuse Removal
- Fuel Pressure Inspection
- Fuel Pump Removal
- Primary Fuel Injector Removal/Installation
- Free Play Inspection
- Idle Speed Inspection/Adjustment
- Nozzle Assy Removal
- Air Cleaner Element Removal/Installation
- Air Inlet Duct Removal
- Fuel Tank Removal
- The Evaporative Emission Control System routes fuel vapors from
- Cooling System
- Coolant Deterioration Inspection
- Water Pump Removal
- Radiator and Radiator Fan Removal
- Thermostat Removal
- Hose Installation
- Water Temperature Sensor Removal/Installation
- Engine Top End
- Compression Gauge, 20 kgf/cm :
- Air Suction Valve Removal
- Cylinder Head Cover Removal
- Camshaft Chain Tensioner Removal
- Camshaft Removal
- Cylinder Compression Measurement
- Valve Clearance Inspection
- Throttle Body Assy Holder Removal
- WARNING
- Clutch
- Clutch Holder:
- Clutch Lever Free Play Inspection
- Clutch Cover Removal
- Clutch Removal
- Engine Lubrication System
- Oil Pressure Gauge, 10 kgf/cm :
- WARNING
- Oil Pan Removal
- Oil Pressure Relief Valve Removal
- Oil Pump Removal
- Oil Cooler Removal
- Oil Pressure Measurement
- Oil Pressure Switch Removal
- Engine Removal/Installation
- Engine Mount Nut Wrench:
- Engine Removal
- Crankshaft/Transmission
- Bearing Puller:
- Crankcase Splitting
- Crankshaft Removal
- Piston Removal
- Starter Clutch Removal
- Starter Idle Gear Removal
- Torque Limiter Removal
- Transmission Shaft Removal
- Shift Pedal Removal
- Wheels/Tires
- Bearing Driver Set:
- Front Wheel Removal
- Air Pressure Inspection/Adjustment
- Hub Bearing Removal
- Final Drive
- Inside Circlip Pliers:
- Drive Chain Slack Inspection
- Engine Sprocket Removal
- Brakes
- Inside Circlip Pliers:
- Brake Lever Position Adjustment
- Front Caliper Removal
- Front Brake Pad Removal
- Front Master Cylinder Removal
- Brake Disc Removal
- Brake Fluid Level Inspection
- Brake Hose Removal/Installation
- Suspension
- Inside Circlip Pliers:
- Rebound Damping Force Adjustment
- Rebound Damping Force Adjustment
- Swingarm Removal
- Tie-Rod Removal
- Steering
- Bearing Puller Adapter:
- Steering Inspection
- Damping Force Adjustment
- Stem, Stem Bearing Removal
- Handlebar Removal
- Frame
- Front Seat Removal
- Lower Fairing Removal
- Side Cover Removal
- Seat Cover Removal
- Front Fender Removal
- Rear Frame Rear Removal
- Windshield Removal
- Mud Guard Removal
- Sidestand Removal
- Rear View Mirror Removal
- Electrical System
- Dummy Page
- Hand Tester:
- There are a number of important precautions that are musts when
- Wiring Inspection
- Battery Removal
- Alternator Cover Removal
- WARNING
- Starter Motor Removal
- This motorcycle adopt the daylight system and have a headlight r
- Air Switching Valve Operation Test
- Fan Motor Inspection
- Meter Unit Removal/Installation
- This motorcycle is equipped with an immobilizer system to protec
- Brake Light Timing Inspection
- Relay Box Removal
- 30 A Main Fuse Removal
- Appendix
- CAL and SEA Models
- CAL and SEA Models
- NOTE

WIRING SCHEMATICS
PARTS CATALOG 2008-09
PARTS CATALOG 2010