Aprilia Tuono 1000 - Workshop Manual / Repair Manual - Wiring Schematics - User Manual

APRILIA TUONO 1000 - WORKSHOP, SERVICE, REPAIR MANUAL - WIRING SCHEMATICS - OWNERS MANUAL


- English Workshop Manual / Repair Manual, User Manual and Wiring Schematics, for motorcycles Aprilia Tuono 1000.
 

MANUALS INCLUDED:

- APRILIA TUONO 1000 SERVICE MANUAL
- APRILIA TUONO 1000 ENGINE SERVICE MANUAL
- APRILIA TUONO 1000 OWNERS MANUAL
- APRILIA TUONO 1000 WIRING SCHEMATICS


INDEX:

0 Introduction
1 General Information
- 1.1 structure of the manual
- 1.2 general rules
- 1.3 dangerous elements
- 1.4 running-in
- 1.5 vehicle identification
2 Periodic Maintenance
- 2.1. general technical information
- 2.1.1 technical data
- 2.1.2 sceduled maintenance chart
- 2.1.3 lubricant table
- 2.1.4 tightening torques
- 2.1.5 special tools
- 2.1.6 location of key components
- 2.1.7 location of instruments/controls
- 2.1.8. instrument panel operation controls
- 2.1.9. systems diagram
3 Fuel System
- 3.1. power supply
- 3.1.1. diagram
- 3.1.2. injection system diagram
- 3.1.3. cylinder synchronisation and co level adjustment
- 3.1.4. axone
- 3.2. fuel pump
- 3.2.1. removing the pump unit
- 3.2.2. removing the fuel level sensor
- 3.2.3. removing the delivery fuel filter
- 3.2.4. removing the fuel pump
- 3.3. throttle body unit
- 3.3.1. removing the throttle body unit
- 3.3.2. disassembling the throttle unit
- 3.3.3. inspecting the throttle unit
- 3.3.4. refitting the throttle unit
- 3.3.5. replacing the throttle valve control lever
- 3.3.6. checking axial play on the throttle valve control shaft
4 Engine
- 4.1. engine
- 4.1.1. removing the engine
- 4.1.2. installing the engine
- 4.1.3. tightening torques
5 Cycle Parts
- 5.1. disassembling the upperworks
- 5.1.1. disassembling the upperworks
- 5.1.2. reassembling the upperworks
- 5.1.3. tightening torques
- 5.2. front fork
- 5.2.1. front fork diagram
- 5.2.2. removing the fork legs
- 5.2.3. fitting the fork legs
- 5.2.4. replacing fork fluid
- 5.2.5. filling the front fork fluid
- 5.2.6. replacing the oil seal/dust seal
- 5.2.7. refitting the oil seal/dust seal
- 5.2.8. checking the components
- 5.2.9. tightening torques
- 5.3. steering bearings
- 5.3.1. diagram
- 5.3.2. checking play
- 5.3.3. adjusting bearing play
- 5.3.4. tightening torques
- 5.4. rear suspension
- 5.4.1. diagram
- 5.4.2. disassembling the rear suspension
- 5.4.3. checking the components
- 5.4.4. reassembling the rear suspension
- 5.4.5. removing the rear suspension connecting rods
- 5.4.6. tightening torques
- 5.5. swingarm
- 5.5.1. removing the swingarm
- 5.5.2. checking the components
- 5.5.3. removing the swingarm bearings
- 5.5.4. refitting the swingarm
- 5.5.5. tightening torques
- 5.6. front wheel
- 5.6.1. diagram
- 5.6.2. removing the front wheel
- 5.6.3. checking the front wheel components
- 5.6.4. removing the front wheel bearings
- 5.6.5. refitting the front wheel bearings
- 5.6.6. fitting the wheel
- 5.7. rear wheel
- 5.7.1. diagram
- 5.7.2. removing the rear wheel
- 5.7.3. removing the final drive unit
- 5.7.4. checking the rear wheel components
- 5.7.5. removing the rear wheel bearings
- 5.7.6. refitting the rear wheel bearings
- 5.7.7. removing the final drive unit bearings
- 5.7.8. refitting the final drive unit bearings
- 5.7.9. removing the vibration damper seals
- 5.7.10. removing the rear sprocket
- 5.7.11. refitting the rear wheel
- 5.7.12. tightening torques
- 5.8. front brake
- 5.8.1. changing the pads
- 5.8.2. check
- 5.8.3. removing the discs
- 5.8.4. bleeding the brake system
- 5.9. rear brake pads
- 5.9.1. replacing the rear brake pads
- 5.9.2. checking the rear brake disc
- 5.9.3. removing the rear brake disc
- 5.10. clutch
- 5.10.1. bleeding the clutch system
- 5.11. chain
- 5.11.1. drive chain
- 5.11.2. inspecting the drive chain slider
- 5.11.3. removing the chain slider
- 5.11.4. lower chain slider
6 Cooling System
- 6.1. cooling system
- 6.1.1. diagram
- 6.1.2. filling the cooling system
7 Electric System
- 7.1. electric system
- 7.1. electric system
- 7.1.1. location of the components
- 7.1.2. electric parts inspection table
- 7.1.3. can line
- 7.1.4. immobilizer
- 7.1.5. lambda sensor
- 7.1.6. recovery function
- 7.1.7. engine rpm limitation condition
- 7.1.8. new mapping
- 7.1.9. wiring diagram